Category
Radiator Additives
Your coolant is dirty, the level keeps dropping, or the temperature runs slightly higher than usual. These are the situations where a radiator additive...
Read more
Your coolant is dirty, the level keeps dropping, or the temperature runs slightly higher than usual. These are the situations where a radiator additive can help you decide between a simple treatment and a garage visit. Radiator additives address two specific problems inside the coolant circuit: internal deposits that reduce heat transfer, and small leaks that cause slow coolant loss. They are maintenance tools, not mechanical repairs.
Subcategories
2 products
What do you actually need: a flush or a stop leak?
Radiator additives fall into two types, and choosing the right one comes down to your specific symptom. A radiator flush dissolves rust, sludge, and scale that build up inside the cooling circuit over time; you add it to the existing coolant, run the engine for the specified period, then drain and refill with fresh coolant. A radiator stop leak circulates through the system and seals small leaks and pinholes from the inside. The two products are not interchangeable, but they can be used in sequence when both problems are present.
Which situation applies to you?
- Dirty or brown coolant, poor heater output, or unknown coolant history: use Lindemann Radiator Flush 350ml before your next coolant change.
- Slow coolant loss, a small drip, or seepage at joints while the car otherwise drives normally: use Lindemann Radiator Stop Leak 350ml added to your existing coolant.
- Both dirty coolant and a small leak: flush and clean the system first, refill with fresh coolant, then add stop leak. Applying stop leak to a contaminated system reduces its effectiveness and increases the risk of deposit-related blockages.
| Radiator Flush | Radiator Stop Leak | |
|---|---|---|
| Main problem | Dirty or brown coolant, deposits, poor heater output | Slow coolant loss, small leaks, seepage at joints |
| When to use | Before a coolant change, or when buying a used car with unknown history | When you notice a small leak but need to keep driving |
| One-time or routine | One-time step during a coolant service, not at every interval | One-time per leak incident, not preventive |
| What it does not fix | Thermostat, water pump, cooling fan, or head gasket faults | Large cracks, broken plastic tanks, split hoses, head gasket failure |
Is this product suitable for your car and coolant type?
Both products are designed for standard passenger car cooling systems. They are suitable for:
- Petrol cars with liquid cooling.
- Diesel cars.
- Hybrid cars with a combustion engine and a conventional coolant circuit.
- Older cars with copper or brass radiators, provided the system is filled with normal automotive coolant.
They are not intended for fully electric vehicles without an engine radiator, industrial cooling systems, domestic heating installations, or systems running on plain water without proper coolant. The additive chemistry relies on the coolant base, so a water-only system is not a suitable application.
Both products are compatible with the following coolant types:
- Conventional ethylene glycol coolant.
- Long-life OAT (Organic Acid Technology) coolants.
- HOAT coolants.
- Ready-mix and concentrate coolants, provided the correct mixture ratio is maintained.
When used at the correct dosage, both products are formulated to be safe for aluminium radiators, plastic expansion tanks, rubber hoses, and standard automotive seals. If your car is still under manufacturer warranty or a fixed service plan, check with your garage if you are unsure. For a full guide on coolant types, the difference between OAT, HOAT, and conventional coolants, and manufacturer change intervals, see our Knowledge Center article on coolant choices.
How do you use a radiator additive correctly?
Always work on a completely cool engine. Opening a pressurised cooling system on a warm engine carries a serious burn risk. Use one 350 ml bottle per standard passenger car cooling system. Do not exceed the recommended dose: overdosing stop leak in particular increases the risk of partial blockage in narrow passages such as the heater core.
Radiator Flush (Lindemann Radiator Flush 350ml)
- Check the coolant level and colour, and confirm the engine is completely cool before opening the system.
- Add one bottle via the expansion tank, or directly into the radiator if it is accessible.
- Close the system, start the engine, and let it reach operating temperature. Run the engine for the period specified on the packaging.
- Let the engine cool down, then drain the old coolant completely. Flush the system with clean water if the product instructions advise it.
- Refill with fresh coolant, bleed the system if needed, and recheck the level after a short drive.
Old coolant is a chemical waste product. Dispose of it according to local regulations and do not pour it down the drain. For the complete mechanical drain and refill procedure, including bleed points and drain taps, see our Knowledge Center guide on cooling system service.
Radiator Stop Leak (Lindemann Radiator Stop Leak 350ml)
- Check the coolant level and assess the leak. Only proceed if coolant loss is slow and the engine is not overheating. If the temperature gauge is already climbing, go to a garage before adding any product.
- On a completely cool engine, add one bottle via the expansion tank, or directly into the radiator if accessible.
- Close the system, start the engine, and let it warm up fully so the additive can circulate through the entire cooling circuit.
- Drive a few kilometres under normal conditions. Small leaks typically seal within one or two drive cycles.
- After the engine cools down, check the coolant level and inspect the leak area. If coolant loss continues, the leak is likely too large for a sealant product.
What can a radiator additive fix, and what can it not fix?
Radiator Flush
Does:
- Dissolves and mobilises rust, sludge, and scale from inside the radiator and cooling circuit.
- Improves heat transfer by cleaning internal surfaces before fresh coolant is added.
- Can support more stable operating temperature and better heater output after a full coolant change.
Does not:
- Repair a faulty thermostat, failed water pump, blocked radiator fins, or cooling fan.
- Fix head gasket damage or structural corrosion holes.
- Replace the coolant. You still need to drain and refill with proper coolant after flushing.
Radiator Stop Leak
Does:
- Seals small internal leaks and pinholes in the radiator core, heater core, or joints from the inside.
- Helps stabilise coolant level in a mildly leaking system.
- Can buy you time until a planned mechanical repair is possible. Small leaks typically seal within a few kilometres of normal driving.
Does not:
- Repair large cracks, broken plastic expansion tanks, or split hoses.
- Stop leaks caused by head gasket failure or oil cooler problems.
- Solve overheating caused by mechanical faults, a blocked radiator, or a failed cooling fan.
When is a radiator additive not enough?
Some symptoms point to a problem that an additive cannot solve. Go to a garage if you notice:
- Coolant loss that is rapid, or that continues after using stop leak.
- Coolant that looks milky or oily. This can indicate head gasket or oil cooler failure, and requires a professional diagnosis.
- The temperature gauge in the red, warning messages on the dashboard, or visible steam from the engine bay. Stop driving immediately.
- Repeated overheating even after a flush and a full coolant refill.
- Coolant hoses that feel very hard, pressure building in the expansion tank, or bubbles in the coolant that suggest combustion gases entering the circuit.
In these situations, a radiator additive is not enough. It is safer to stop driving and have a garage diagnose the cooling system.
Can you use a radiator additive as preventive maintenance?
A radiator flush is a sensible one-time step when you buy a used car with an unknown coolant history, or when coolant is due for replacement and the fluid looks discoloured. It is not intended for routine use at every service interval; use it when there is a clear reason. Radiator stop leak is not a preventive product. You should not add it to a system that has no leak, as it is designed for a specific situation and used once per incident. For long-term corrosion protection between coolant changes, coolant conditioner products exist, but they are not part of the current DPP radiator additive range. The most reliable approach is to follow the manufacturer's coolant change interval and use the correct coolant type for your car.
If you are unsure whether your situation calls for a flush, a stop leak, or a garage visit, the symptom lists above are the quickest guide. When in doubt, start with the problem you can see: dirty coolant points to a flush, a slow drip points to stop leak, and anything more serious points to a mechanic.
Knowledge Center
Read more if you are still unsure

Need help choosing?
Ask us for advice on the right product for your vehicle and maintenance needs.